Field guide
Orbital and TIG welders for fab tube and pipe
Fab welding work splits into two trades: orbital welders who run machine welds on small-diameter 316L tube for gas and chemical lines, and manual TIG welders who weld process pipe, tie-ins and anything an orbital head cannot reach. The guides below follow the order a hiring decision usually takes, from scope to the first weeks on site.
What this field covers
| Trade | Typical work | What decides the hire |
|---|---|---|
| Orbital welder | Autogenous orbital GTAW on 316L EP/BA tube; head and power-supply setup, weld schedules, purge control | Coupon welds to your schedule, borescope result, setup and log discipline |
| TIG (GTAW) welder | Manual GTAW on stainless and carbon steel pipe; root, fill and cap in all positions | Performance test to your WPS, position and diameter range, back-purge on stainless roots |
Pipers, fitters, foremen and QA/QC work next to these welders and are covered in their own fields. For the six roles WELDK sources and the seven-step process, see capabilities by role.
Before you hire: scope and qualification
Overview: Fab welding: before you hire →
- Before you hireManual TIG or orbital welder: which does your fab scope need?Match each part of a semiconductor or battery plant scope to orbital or manual TIG welders, and see where the two trades overlap.
- Before you hireWelder or welding operator: qualifying orbital tube weldersWhy orbital welders are qualified as welding operators, what Korean certificates do and do not prove, and how employers qualify new hires.
- Before you hireFab or pharma orbital experience: what transfers to a semiconductor siteWhich skills from pharmaceutical, biotech or food orbital welding carry over to semiconductor gas lines, and which ones you should test again.
- Before you hireWriting an orbital welder requirement for UHP gas linesWhat to put in an orbital welder requirement for semiconductor gas lines so candidates can be matched, interviewed and tested without guesswork.
- Before you hireStainless, carbon steel or duplex: matching TIG welders to your pipe materialsWhich pipe materials on a fab or battery plant scope change what you require from a manual TIG welder, and what to test for each one.
- Before you hireWhat orbital welding is, and when a project needs orbital weldersA plain explanation of orbital welding for employers and project managers: how an orbital welder works, where it is used and why fab gas lines need it.
Choosing candidates and budgeting
Overview: Fab welding: choosing candidates and budgeting →
- Choosing and budgetingWhat decides the cost of hiring a welder from KoreaThe cost items an overseas employer budgets when hiring a Korean welder directly, who usually pays each one, and what moves the total.
- Choosing and budgetingDirect hire, staffing agency or subcontract crew for fab weldersCompare direct hire, staffing agencies and subcontracted crews for fab welding work: who employs, who controls the work and who carries which costs.
- Choosing and budgetingHow to read a welder profile: stated, reviewed and testedWhat each item on a WELDK candidate profile means, how far it has been checked, and the follow-up question to ask for each one.
- Choosing and budgetingQuestions to ask before using a welder recruiterThe questions that show how a welder recruiter or introducer works: who pays, how candidates are checked, what you receive and what is not guaranteed.
Interviews, tests and schedule
Overview: Fab welding: interviews, tests and schedule →
- Tests and scheduleRunning a weld test for a welder who is still in KoreaThree ways to test an orbital or TIG welder before they travel, what each one proves, and a checklist for the coupon and the video.
- Tests and scheduleWhat sets the timeline for hiring a welder from KoreaThe stages between a request and a Korean welder’s first day on an overseas fab site, what each one depends on and what the employer can do to shorten it.
- Tests and scheduleInterviewing a welder in Korea: time zones, interpreters and structureHow to plan a remote interview with a welder in Korea: scheduling across time zones, using an interpreter well and structuring technical questions.
- Tests and scheduleWork authorization checks to finish before offering a job to a welder from KoreaThe work authorization questions an employer should settle with immigration counsel before offering a job to a welder from Korea, and what WELDK does not do.
- Tests and scheduleChanging the scope after interviews: when candidates need a new testWhen a change to materials, sizes, equipment or positions after interviews means candidates must be retested, and how to handle it without losing them.
After the hire: quality and onboarding
Overview: Fab welding: after the hire →
- After the hireCommon orbital weld defects on UHP tube and what they tell youDiscoloration, incomplete penetration, misalignment and other orbital weld faults on 316L UHP tube, their usual causes, and what to ask the welder.
- After the hireOnboarding Korean welders on an overseas fab siteA first-two-weeks plan for Korean welders arriving on an overseas fab site: induction, language, equipment, first welds and daily life.
- After the hireBattery plant or semiconductor fab: what changes for weldersHow welding work differs between battery plants and semiconductor fabs, and how to judge a welder whose experience comes from the other plant type.
- After the hireSwitching orbital equipment brands: what a new hire needs to relearnWhat carries over when an orbital welder moves to a different brand of power supply and weld head, and how to plan supervised coupons before production.
- After the hireWhen a new welder keeps failing: retrain, retest or replaceA decision path for an employer whose newly hired welder keeps producing rejected welds: find the cause, then retrain, retest or end the assignment fairly.
Cases from real projects
No fab welding placement has been completed through WELDK yet, so this section is empty on purpose. When an engagement finishes and the employer agrees, its case page will be listed here with the actual site, scope and outcome.
Frequently asked questions
Where is plastic piping covered?
In the UHP piping guides. PVDF, PFA and PP lines are joined with fusion or fitting methods, not welded by TIG or orbital welders.
Which guide should we read first?
If the scope is still open, start with the manual TIG or orbital question. If you already know the roles, go to qualification and the weld test for a welder who is still in Korea.
Have a fab scope that needs these trades?
Requests are in preview: you can fill in the request form, but it does not submit yet. Email WELDK with your roles, site country and start window.